Human 17-α-hydroxylase ((17-α-OH) enzyme-linked immunoassay (ELISA)
Kit instruction manual
This reagent is for research purpose only: This kit is used to determine the content of 17-α-hydroxylase ((17-α-OH) in human serum, plasma and related liquid samples.
Experimental principle:
This kit uses the double antibody sandwich method to determine the level of human 17-α-hydroxylase ((17-α-OH) in the specimen. Use purified human 17-α-hydroxylase ((17-α-OH) antibody package Prepare a solid-phase antibody in a microwell plate. Add 17-α-hydroxylase ((17-α-OH) to the monoclonal antibody-coated microwells in turn, followed by HRP-labeled 17-α-hydroxylase ( (17-α-OH) antibody binds to form an antibody-antigen-enzyme-labeled antibody complex, and after thorough washing, the substrate TMB is used for color development. TMB is converted to blue under the catalysis of HRP enzyme and under the action of acid Converted to the final yellow color. The shade of the color is positively correlated with the 17-α-hydroxylase ((17-α-OH) in the sample. The absorbance (OD value) is measured with a microplate reader at a wavelength of 450 nm and calculated by a standard curve The concentration of human 17-α-hydroxylase ((17-α-OH) in the sample.
Kit composition:
Kit composition
48 hole configuration
96-well configuration
save
Instructions
1 serving
1 serving
Sealing film
2 pieces (48)
2 pieces (96)
sealed bag
1
1
Enzyme coated plate
1 × 48
1 × 96
Store at 2-8 ℃
Standard product: 45μg / L
0.5ml × 1 bottle
0.5ml × 1 bottle
Store at 2-8 ℃
Standard dilution
1.5ml × 1 bottle
1.5ml × 1 bottle
Store at 2-8 ℃
Enzyme reagent
3 ml × 1 bottle
6 ml × 1 bottle
Store at 2-8 ℃
Sample diluent
3 ml × 1 bottle
6 ml × 1 bottle
Store at 2-8 ℃
Developer A liquid
3 ml × 1 bottle
6 ml × 1 bottle
Store at 2-8 ℃
Developer B liquid
3 ml × 1 bottle
6 ml × 1 bottle
Store at 2-8 ℃
Stop solution
3ml × 1 bottle
6ml × 1 bottle
Store at 2-8 ℃
Concentrated washing liquid
(20ml × 20 times) × 1 bottle
(20ml × 30 times) × 1 bottle
Store at 2-8 ℃
Sample processing and requirements:
1. Serum: room temperature blood coagulates naturally for 10-20 minutes, centrifuged for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully and centrifuge again if a precipitate appears during storage.
2. Plasma: EDTA or sodium citrate should be selected as the anticoagulant according to the requirements of the specimen, mixed for 10-20 minutes, and centrifuged for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. If a precipitate forms during storage, it should be centrifuged again.
3. Urine: collected in a sterile tube and centrifuged for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. If a precipitate forms during storage, centrifuge again. Pleural and ascites, cerebrospinal fluid reference implementation.
4. Cell culture supernatant: When detecting secreted components, collect with a sterile tube. Centrifuge for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. When detecting the components inside the cells, dilute the cell suspension with PBS (PH7.2-7.4), and the cell concentration will reach about 1 million / ml. Through repeated freezing and thawing, the cells are destroyed and the intracellular components are released. Centrifuge for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. If a precipitate forms during storage, it should be centrifuged again.
5. Organize the specimen: after cutting the specimen, weigh it. Add a certain amount of PBS, PH7.4. Quickly freeze and save with liquid nitrogen for later use. After the specimen melts, it still maintains a temperature of 2-8 ° C. Add a certain amount of PBS (PH7.4) and homogenize the specimen with a manual or homogenizer. Centrifuge for about 20 minutes (2000-3000 rpm). Collect the supernatant carefully. After aliquoting, a portion is to be tested, and the rest is frozen for future use.
6. The specimen should be extracted as soon as possible after collection. The extraction should be carried out according to relevant literature. The experiment should be carried out as soon as possible after extraction. If the test cannot be performed immediately, the specimen can be stored at -20 ℃, but repeated freezing and thawing should be avoided.
7. The sample containing NaN3 cannot be detected because NaN3 inhibits the activity of horseradish peroxidase (HRP).
Steps
1. Dilution and loading of standard products: set 10 standard wells on the enzyme-coated plate, add 100 μl of standard products in the first and second wells, and then add standard products in the first and second wells 50μl of diluent, mix well; then take 100μl from the first well and the second well and add them to the third and fourth wells respectively, and then add 50μl of standard diluent to the third and fourth wells respectively, mix well; Then take 50μl each in the third and fourth wells and discard it, then add 50μl each to the fifth and sixth wells, and then add 50ul of the standard dilution solution to the fifth and sixth wells respectively, and mix well; After mixing, take 50μl from the fifth and sixth wells and add them to the seventh and eighth wells respectively. Then add 50μl of the standard dilution solution to the seventh and eighth wells respectively. Take 50μl from the eight wells and add them to the ninth and tenth wells. Then add 50μl of the standard dilution solution to the ninth and tenth wells. After mixing, take 50μl from the ninth and tenth wells and discard. (After dilution, the volume of each well is 50μl, and the concentration is 30μg / L, 20μg / L, 10μg / L, 5μg / L, 2.5μg / L).
2. Add samples: set up blank wells (the blank control wells do not add samples and enzyme reagents, the rest of the steps are the same) and the sample wells to be tested. Add 40μl of sample diluent to the test sample well of the enzyme-coated plate, and then add 10μl of the sample to be tested (the final dilution of the sample is 5 times). Add the sample and add the sample to the bottom of the well of the microplate, try not to touch the wall of the well, shake gently to mix.
3. Incubation: Seal the plate with a sealing plate and incubate at 37 ° C for 30 minutes.
4. Mixing solution: Dilute 30 times (20 times of 48T) concentrated washing liquid with distilled water 30 times (20 times of 48T) and then use.
5. Washing: Carefully peel off the sealing film, discard the liquid, spin dry, fill each well with the washing liquid, let it stand for 30 seconds and then discard, repeat this 5 times, pat dry.
6. Add enzyme: add 50μl of enzyme label reagent to each well, except blank well.
7. Incubation: The operation is the same as 3.
8. Washing: The operation is the same as 5.
9. Color development: add 50μl of developer A to each well, then add 50μl of developer B, mix gently, and develop at 37 ° C in the dark for 15 minutes.
10. Termination: Add 50μl of stop solution to each well to stop the reaction (at this time the blue will turn to yellow).
11. Determination: Measure the absorbance (OD value) of each well in sequence with the blank air conditioner at zero and 450 nm wavelength. The measurement should be carried out within 15 minutes after adding the stop solution.
Precautions:
1. The kit should be equilibrated at room temperature for 15-30 minutes before being taken out of the refrigerated environment. If the enzyme label coated plate is unopened, the strip should be stored in a sealed bag.
2. Crystals may be precipitated in the concentrated washing liquid, which can be heated and dissolved in a water bath during dilution, and the results will not be affected during washing.
3. The sampler should be used at each step of sample addition, and the accuracy should be regularly checked to avoid test errors. It is best to control the sampling time within 5 minutes. If there are many specimens, it is recommended to use a volley gun to add samples.
4. Please make a standard curve at the same time of each measurement, it is best to make a double hole. If the content of the test substance in the specimen is too high (the OD value of the sample is greater than the OD value of the first well of the standard well), please first dilute it with a certain multiple (n times) of the sample diluent and then determine it. When calculating, please multiply the total dilution Multiple (× n × 5).
5. The sealing film is limited to one-time use to avoid cross-contamination.
6. Please keep the substrate away from light.
7. Strictly follow the instructions, and the test results must be determined by the microplate reader.
8. All samples, washing liquids and various wastes should be treated as infectious agents.
9. The components of different batches of this reagent shall not be mixed.
10. If there is any difference with the English manual, the English manual shall prevail.
Calculation:
Taking the concentration of the standard as the abscissa and the OD value as the ordinate,
Draw a standard curve on coordinate paper, according to the OD of the sample
The value is determined by the standard curve; then multiplied by the dilution
Multiple; or calculate the standard using the concentration and OD value of the standard
The linear regression equation of the quasi-curve, the OD value of the sample
Substitute into the equation, calculate the sample concentration, and multiply by the dilution
The multiple is the actual concentration of the sample.
(This picture is for reference only)
Kit performance:
1. The correlation coefficient R between the linear regression of the sample and the expected concentration is more than 0.990.
2. The batch and approval shall be less than 9% and 11% respectively
examination range:
2μg / L -40μg / L
Storage conditions and validity period:
1. Store the kit: 2-8 ℃.
2. Validity: 6 months
Outdoor furniture refers to furniture used for outdoor environment, mainly used for outdoor leisure, entertainment and dining activities. The classification of outdoor furniture can be divided according to the material, function and shape.
First, classification by material
1. Wooden outdoor furniture: Wooden outdoor furniture is usually made of natural wood, such as teak. Wooden furniture has a natural, rustic character and is suitable for outdoor Spaces such as gardens, terraces and courtyards.
2. Metal outdoor furniture: Metal outdoor furniture is usually made of iron, aluminum, stainless steel and other metal materials. Metal furniture has the characteristics of durability and stability, suitable for long-term use in outdoor environment.
3. Cloth outdoor furniture: Cloth outdoor furniture is usually made of waterproof, sun protection and other special treatment of fabric. Fabric furniture with soft, comfortable characteristics, suitable for use in outdoor leisure areas.
Second, Classification by function
1. Leisure Chair: Leisure chair is the most common kind of outdoor furniture, usually used for outdoor leisure, sunbathing and other activities. There are a variety of leisure chairs, folding chairs, recliners, rocking chairs and so on.
2. Dining Table And Chair: Dining table and chair are mainly used for outdoor dining, usually consisting of a table and several chairs. Dining tables and chairs of various styles, there are round tables, square tables, etc., suitable for different venues and the number of people dining needs.
3. Parasol: Parasol is used for outdoor shading, which can effectively block direct sunlight and provide a cool resting environment. There are various styles of sunshade umbrellas, including ordinary umbrellas, large umbrellas, and rotating umbrellas.
Third, Classification by shape
1. Chairs: including ordinary chairs, rocking chairs, recliners, etc., suitable for outdoor leisure and sun.
2. Table category: including dining table, coffee table, side table, etc., suitable for outdoor dining and placing items.
3. Sofa category: including single sofa, double sofa, combination sofa, etc., suitable for outdoor leisure and parties.
4. Reclining chairs: including hammocks, reclining chairs, etc., suitable for outdoor naps and rest.
5. Queue class: including benches, benches, etc., suitable for outdoor queuing and waiting.
In summary, the classification of outdoor furniture can be divided according to material, function and shape. Different outdoor furniture is suitable for different outdoor environment and activity needs, choose suitable outdoor furniture can provide comfortable and convenient outdoor life experience.
Outdoor Table,Rattan Table,Rattan Chair,Beach Furniture
Foshan Shengshi Zhihui Technology Co., Ltd. , https://www.szhfurniture.com